Syvecs S911 PnP kit brings a new level of Engine Management control to the Porsche 996 and 997 Turbo range of cars. Offering complete control of the engine management system and gearbox torque control live on all models including the Tiptronics and GT Ranges. (Worlds First Standalone management!)

Compatible with OEM VTG Turbos

By simply pluging in the PnP kit, a whole new level of control is available offering the following features:

• Live tuning of every aspect of the engine’s calibration, including signals sent to the TCM and 4WD
• Increased tiptronic shift speeds with torque reduction via fuel cut and retard. Far superior over the stock ECU throttle angle adjustment
• Adjustable shift RPM with speed lockout on tiptronic cars
• Ability to select desired engine map, boost level, traction and launch control levels through OEM steering wheel buttons or external 12 position switch. Indicated map is shown on "Boost Level" (See Media)
• Flex fuel control
• Immobiliser and PSM Module communication as OEM
• Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
• Fully adjustable launch control with anti-lag strategies and ramp in maps. 12 live switchable maps available
• Fully adjustable traction control system with lateral G targeting.  12 live switchable maps available
• Full VVT (Variable Valve Timing) and lift control
• Closed loop dual lambda control utilising OEM lambda sensors
• Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
• Monitor and trimming of exhaust gas temperatures
• Built in data logging with market leading analysis software of up to 8 hours, with data rates at up to 1000hz
• Rolling antilag and pit lane limiter strategies, great for building boost on a roll
• Antitheft and valet modes
• Super fast connection via Ethernet port for live tuning anywhere in the world or even remotely if on track and connected to a wireless unit.
• Configurable engine safety trips on all important parameters like oil temperature, oil pressure, water temp and crankcase pressure.
• Fuel pump control of both main, and sub pumps, as well as relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• 4 different Pedal to Throttle angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
• Ability to change torque levels or demand levels sent to 4WD unit and TCM ECU
• Change torque reduction levels on shifts. Essential for very high power tiptronic versions where the maximum reduction available via the stock ECU is not enough to prevent damage to components
• Ability to change torque ramp in after launch
• Change throttle blip requests to match your torque band which is especially useful on oversized turbo installations.
• Run up to 7bar map sensors
• Control high or low impendence injectors
• Control up to 12 injectors for high power installations where staged injection may be required
• Change injector dead times based on voltage levels for proper control
• Change injector end angle to ensure injection point is properly calibrated
• Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
• Ability to use any size DBW throttle body e.g. Chevrolet LS7
• Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
• Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
• Connect any race series dash or even one of our partners’ Touchscreen CANBUS adjustment /display units
• View any input live with built in scope up to 1000hz
• and much, much more!

The Syvecs Porsche 996 Plug N Play Kit brings a new level of engine management control to the Porsche 996 platform.

Offering complete control of the engine management system and gearbox torque control live on all models including the Tiptronics and GT ranges. (Worlds First Standalone management!)

By simply pluging in the kit a whole new level of control is available offering the following features and more:

• Live tuning of every aspect of the engine’s calibration, including signals sent to the TCM and 4WD
• Increased Tiptronic shift speeds with torque reduction via Fuel cut and retard. Far superior over the stock ECU throttle angle adjustment
• Adjustable shift RPM with speed lockout on tiptronic cars
• Ability to select desired engine map, boost level, traction and launch control levels through the OEM Steering wheel buttons or and optional external 12 position switch. Indicated map is shown on boost level (See Media)
• Flex Fuel Control
• Immobiliser and PSM Module communication as OEM
• Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
• Fully adjustable launch control with anti-lag strategies and ramp in maps. 12 live switchable maps available
• Fully adjustable traction control system with Lateral G targeting.  12 live switchable maps available
• Full Variable Valve Timing and lift control
• Closed loop dual lambda control utilising OEM lambda sensors
• Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
• Monitor and trimming of exhaust gas temperatures
• Built in data logging with market leading analysis software of up to 8 hours, with data rates at up to 1000hz
• Rolling Antilag and pit lane limiter strategies, great for building boost on a roll
• Antitheft and valet modes
• Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or even remotely if on track and connected to a wireless unit.
• Configurable engine safety trips on all important parameters like oil temperature, oil pressure, water temp and crankcase pressure.
• Fuel pump control of both main, and sub pumps, as well as relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• 4 different pedal to throttle angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
• Ability to change torque levels or demand levels sent to 4WD unit and TCM ECU
• Change torque reduction levels on shifts. Essential for very high power tiptronic versions where the maximum reduction available via the stock ECU is not enough to prevent damage to components
• Ability to change torque ramp in after launch
• Change throttle blip requests to match your torque band. Especially useful on oversized turbo installations.
• Run up to 7bar map sensors
• Control high or low impendence injectors
• Control up to 12 injectors for high power installations where staged injection may be required
• Change injector dead times based on voltage levels for proper control
• Change injector end angle to ensure injection point is properly calibrated
• Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
• Ability to use any size DBW throttle body e.g. Chevrolet LS7
• Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
• Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
• Connect any race series dash including our own Syvecs Edition SDM displays
• View any input live with built in scope up to 1000hz
• and much, much more

Fitment: Porsche 991.1 991.2 Turbo, Turbo S

The 991 Turbo Eventuri intake system was developed through extensive real world testing with the aim of allowing the turbos to work more efficiently. By replacing the single stock airbox with individual patented Venturi filter housings, the turbos are able to spool and generate boost with less drag. As a result, the wastegate duty cycles are reduced resulting in peak boost at lower RPM and therefore performance is increased. The two individual filters provide a larger filtration area as compared to the single stock panel filter. Furthermore, in order to keep inlet air temperatures down, the Venturi housings are sealed against an air duct which draws ambient air from the same location as the stock system. Since the 911 Turbo engine bay is densely packed, high IATs can only be avoided by ensuring a fully sealed intake system. The combination of a smoother airflow path to each turbo with low IATs results in higher performance and a sharper throttle response over the stock airbox.

EVE-C8RS6-CF-INT : Audi C8 RS6/RS7 Intake GLOSS carbon
EVE-C8RS6-CFM-INT : Audi C8 RS6/RS7 Intake MATTE carbon

AUDI C8 RS6 RS7

Performance Increase – Stock ECU : 15-25hp, 11-20ft-lbs
Performance Increase – Stage 1* : 45-50hp, 40-45ft-lbs
Stage 1 Acceleration 100-200Km/h : Reduced by 0.6s
Performance Increase – Stage 2* : 60-80hp, 60-70ft-lbs

The Audi C8 RS6 intake system is the culmination of extensive development, testing and prototyping. Our aim was to address 2 main criteria: 1) Increased flow rate. 2) Smooth Airflow. The first objective was met by utilising all of the limited space available in the RS6 engine bay which was heavily restricted by the underside of the hood. Our solution was to completely redesign the entire airbox which maximized volume, increased flow entry openings and created a more favourable filter angle to the turbos. Furthermore we dramatically increased the size of the turbo inlets by as much as 85% when measuring the cross sectional area at the openings. The second objective was met by designing an organically shaped system with a custom rounded panel filter to ensure the airflow path contained no sharp corners and therefore allowed for the flow to remain laminar. With smooth transitions from the filter to the turbo inlets, our intake minimises the formation of turbulence and therefore the turbos are able to operate more efficiently. We partnered with BMC for a bespoke filter element to ensure that the filtration area is as large as possible whilst keeping airflow clean.

With all objectives met, our C8 RS6 intake system delivers on all fronts and allows for the turbos to generate boost more efficiently. This results in an improved throttle response and significant power gains, independently tested which increase with higher states of tune. The performance gains measured are a result of the complete system we have developed from the airbox base to the lid and the inlets.

*Gains measured can vary with different ECU tunes.

Part Numbers:
EVE-A90-CF-INT : Toyota MK5 Supra Carbon Intake

Performance Gain: 17-20hp, 11-20ft-lb

The MK5 Supra Eventuri intake has been developed to provide the turbo with a less restrictive flow path whilst maintaining low inlet temperatures. Heat and Volume are the main considerations when designing an intake for turbocharged engines. In the Supra, the intake system is located next to the exhaust manifold which rapidly heat soaks the engine bay. High temperatures are detrimental for engine performance as the turbo would have to build boost with heated, less dense air and so the only way to ensure IAT’s are kept to a minimum is for a fully sealed intake. This however, results in a restriction with only one stock air feed to draw air in from. During development we noticed an additional opening into the wheel arch area and took advantage of this by adding a secondary feed to our airbox. Furthermore our sealed airbox also has a heat shield with gold reflective to minimize the radiative heat transfer from the exhaust manifold. In order to maximize volume we made the airbox as large as possible with a recess for potential strut braces. The stock convoluted intake tube is replaced with a smooth carbon tube which is also larger in internal volume with a starting internal diameter of 111mm (4.4″) smoothly tapering down to match the turbo inlet. The tube provides a smooth path from the filter to the turbo inlet. Finally we use a custom made high-flow dry filter which is ISO tested for filtration performance and has a larger filtration area than the stock filter.

Installation Guide HERE

Part Numbers:
EVE-C63S-CF-INT : Mercedes all AMG C63/C63S variants Carbon intake with carbon ducts

Performance Increase – Stage 2 : 22-30hp, 20-24ft-lb
Performance Increase – Stock : 10-12hp, 12-15ft-lb
Flowbench Data : Stock Airbox 381 CFM : Eventuri 531 CFM (Average Per Airbox)

Fitment for the following models: W205 S205 C205 A205 C63 C63S AMG

The Mercedes W205 C63S AMG intake system is the culmination of extensive development and testing. Our design brief consisted of 3 main objectives: 1) Increased flow rate. 2) Low intake temperatures. 3) Smooth airflow. The first objective was met by utilising all of the limited space available in the C63S engine bay resulting in a 39% higher flow rate over the stock system. The second objective was met by designing a fully sealed system. The C63S engine bay reaches high temperatures with heat sources like the turbos in close proximity to the intake so it is crucial that the intake remains sealed. The final objective was met by designing an organically shaped system with custom rounded panel filters to ensure the airflow path contained no sharp corners and therefore allowed for the flow to remain laminar. With smooth transitions from the filters to the turbo inlets, our intake minimises the formation of turbulence and therefore the turbos are able to operate more efficiently.

With all 3 objectives met, our W205 C63S intake system delivers on all fronts and allows for the turbos to generate boost more efficiently. This results in an improved throttle response and genuine power gains which increase with higher states of tune. Since there are various turbo upgrades available for the C63S we have also catered a specific solution for larger turbos. Our C63S intake is available in 2 configurations: 61mm ID outlets to match the stock and hybrid turbos and 3″ ID outlets to match larger aftermarket turbos.

Installation Guide HERE

• Eliminates Heat Soak and Lowers Air Intake Temperatures (IATs) for Maximum Performance in Race Conditions – Especially Critical Due to Intercooler Placement in Engine Compartment
• Formula-1 Performance Grade Core by PWR (2-Row Core Featuring Rolled Tubes w/ Inner Fins)
  • 33 Tubes vs. OEM 17
  • 3mm Rolled Tube vs. OEM 7mm
  • 4.85mm Fin Height vs. OEM 8mm
• CNC Machined Billet End Tanks With Integrated Y-Pipe Connection to Throttle Body
• 100% TIG Welded vs. OEM Style Gasket and Crimped Plastic End Tanks for Maximum Durability in High Boost Applications
• OEM Style CNC Machined Inlet/Outlet Connections for Precise Fitment with All OEM Components
• Highly Engineered, Lightweight Design – Weighing Only 20 lbs. Total (9.07 kg)
• True Plug-and-Play “Drop-in Fit” Installation
• R&D and Performance Testing by Industry-Leading Porsche Tuning Companies – M-Engineering, World Motorsports, GMG Racing, and Gosha Turbo Tech
• Made in the USA at PWR North America
• Fits:
  • 2020+ Porsche 992 Turbo
  • 2020+ Porsche 992 Turbo S
  • OEM # 992.145.805.G

The Porsche 992 Turbo M-Tuner Suite by M-Engineering was developed from the ground up over many months of testing, starting overseas with the help of our dealers before being the first in the US to start tuning these cars. M-Engineering has been at the forefront of Porsche ECU tuning, and has spent countless hours of research and development to provide reliable performance improvements.

M-Tuner Calibration Suite will allow at-home OBD flashing, no ECU removal is necessary. Software also features the ability to read and clear faults, datalog, view live data, and flash back to stock at your convenience.

Adjustments are made to improve the throttle response, remove top speed limiters, adjust air/fuel ratios, increase boost, and modify ignition timing and much more to improve the overall driving performance of the 3.7L twin-turbocharged engine. M-Engineering still utilizes all OEM ECU engine safety strategies.

What's Included?

M-Tuner Dongle for OBD Flashing
USB Cable
M-Engineering maps built for your 992 Turbo (see calibration notes)
Ability to go back to stock
M-Engineering Support
We have maps available in Stage 1 and Stage 2 configurations in 91, 93, and 100 octane.

These are the current vehicles supported by this version of M-Tuner. Please review calibration notes below for more information regarding hardparts requirements, octane requirements, and additional dyno plots.

992 Turbo S

Turbo Base: Official numbers coming soon!

Turbo S: Our Stage 1 tune results in an increase of approximately +114whp & +145ft-lbs tq on 93 octane.

With a basic Stage 1 calibration the 992 Turbo S can make 700whp on 91 octane(95 RON), 721whp on 93 octane (98RON), and 751whp on 100oct (104 RON). Our refined calibration takes a stock 992 Turbo S and turns it into a reliable 9 second 1/4 mile car!

M-Engineering has been at the forefront of Porsche ECU tuning, and has spent countless hours of research and development to provide reliable performance improvements.

M-Tuner Calibration Suite will allow at-home OBD flashing, no ECU removal is necessary. Our software also features the ability to read and clear faults, datalog, view live data, and flash back to stock at your convenience.

Adjustments are made to improve the throttle response, remove top speed limiters, adjust air/fuel ratios, increase boost, and modify ignition timing and much more to improve the overall driving performance of the 3.0L twin-turbocharged engine. M-Engineering still utilizes all OEM ECU engine safety strategies.

Compatible with 992 Carrera, Carrera 4, Carrera S, and Carrera 4S.

What's Included?

• M-Tuner Dongle for OBD Flashing
• USB Cable
• M-Engineering maps built for your 992 Carrera (see calibration notes)
• Ability to go back to stock
• M-Engineering Support

We have maps available in Stage 1 and Stage 2 configurations in 91, 93, 100, and E85. 

These are the current vehicles supported by this version of M-Tuner. Please review calibration notes below for more information regarding hardparts requirements, octane requirements, and additional dyno plots. 

992 Carrera

992 Carrera S

992 Carrera GTS - Coming Soon! 

Installation instructions are located here.

Carrera Base: Our Stage 1 tune results in an increase of approximately +61whp & +106ft-lbs tq on 93 octane. 

Carrera S: Our Stage 1 tune results in an increase of approximately +146whp & +51ft-lbs tq on 93 octane.

With the M-Engineering ECU flash for the Lamborghini Urus, adjustments are made to improve the throttle response, increase boost, remove top speed limiters, adjust air/fuel ratios, and modify ignition timing and much more to improve the overall driving performance of the 4.0L engine. M-Engineering still utilizes all OEM ECU engine safety strategies. 

With the Stage 1 tune you can expect an increase of +86whp and +92ft-lbs tq. 

PLEASE NOTE - FOR THIS PRODUCT WE WILL NEED YOUR ECU SHIPPED TO US.