Includes:

4 bar motorsports grade stainless MAP sensor

4bar Bosch pre-throttle pressure sensor

Plug and play wiring adapters

Syvecs S911 PnP kit brings a new level of Engine Management control to the Porsche 996 and 997 Turbo range of cars. Offering complete control of the engine management system and gearbox torque control live on all models including the Tiptronics and GT Ranges. (Worlds First Standalone management!)

Compatible with OEM VTG Turbos

By simply pluging in the PnP kit, a whole new level of control is available offering the following features:

• Live tuning of every aspect of the engine’s calibration, including signals sent to the TCM and 4WD
• Increased tiptronic shift speeds with torque reduction via fuel cut and retard. Far superior over the stock ECU throttle angle adjustment
• Adjustable shift RPM with speed lockout on tiptronic cars
• Ability to select desired engine map, boost level, traction and launch control levels through OEM steering wheel buttons or external 12 position switch. Indicated map is shown on "Boost Level" (See Media)
• Flex fuel control
• Immobiliser and PSM Module communication as OEM
• Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
• Fully adjustable launch control with anti-lag strategies and ramp in maps. 12 live switchable maps available
• Fully adjustable traction control system with lateral G targeting.  12 live switchable maps available
• Full VVT (Variable Valve Timing) and lift control
• Closed loop dual lambda control utilising OEM lambda sensors
• Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
• Monitor and trimming of exhaust gas temperatures
• Built in data logging with market leading analysis software of up to 8 hours, with data rates at up to 1000hz
• Rolling antilag and pit lane limiter strategies, great for building boost on a roll
• Antitheft and valet modes
• Super fast connection via Ethernet port for live tuning anywhere in the world or even remotely if on track and connected to a wireless unit.
• Configurable engine safety trips on all important parameters like oil temperature, oil pressure, water temp and crankcase pressure.
• Fuel pump control of both main, and sub pumps, as well as relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• 4 different Pedal to Throttle angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
• Ability to change torque levels or demand levels sent to 4WD unit and TCM ECU
• Change torque reduction levels on shifts. Essential for very high power tiptronic versions where the maximum reduction available via the stock ECU is not enough to prevent damage to components
• Ability to change torque ramp in after launch
• Change throttle blip requests to match your torque band which is especially useful on oversized turbo installations.
• Run up to 7bar map sensors
• Control high or low impendence injectors
• Control up to 12 injectors for high power installations where staged injection may be required
• Change injector dead times based on voltage levels for proper control
• Change injector end angle to ensure injection point is properly calibrated
• Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
• Ability to use any size DBW throttle body e.g. Chevrolet LS7
• Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
• Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
• Connect any race series dash or even one of our partners’ Touchscreen CANBUS adjustment /display units
• View any input live with built in scope up to 1000hz
• and much, much more!

The Syvecs Porsche 996 Plug N Play Kit brings a new level of engine management control to the Porsche 996 platform.

Offering complete control of the engine management system and gearbox torque control live on all models including the Tiptronics and GT ranges. (Worlds First Standalone management!)

By simply pluging in the kit a whole new level of control is available offering the following features and more:

• Live tuning of every aspect of the engine’s calibration, including signals sent to the TCM and 4WD
• Increased Tiptronic shift speeds with torque reduction via Fuel cut and retard. Far superior over the stock ECU throttle angle adjustment
• Adjustable shift RPM with speed lockout on tiptronic cars
• Ability to select desired engine map, boost level, traction and launch control levels through the OEM Steering wheel buttons or and optional external 12 position switch. Indicated map is shown on boost level (See Media)
• Flex Fuel Control
• Immobiliser and PSM Module communication as OEM
• Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
• Fully adjustable launch control with anti-lag strategies and ramp in maps. 12 live switchable maps available
• Fully adjustable traction control system with Lateral G targeting.  12 live switchable maps available
• Full Variable Valve Timing and lift control
• Closed loop dual lambda control utilising OEM lambda sensors
• Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
• Monitor and trimming of exhaust gas temperatures
• Built in data logging with market leading analysis software of up to 8 hours, with data rates at up to 1000hz
• Rolling Antilag and pit lane limiter strategies, great for building boost on a roll
• Antitheft and valet modes
• Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or even remotely if on track and connected to a wireless unit.
• Configurable engine safety trips on all important parameters like oil temperature, oil pressure, water temp and crankcase pressure.
• Fuel pump control of both main, and sub pumps, as well as relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• 4 different pedal to throttle angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
• Ability to change torque levels or demand levels sent to 4WD unit and TCM ECU
• Change torque reduction levels on shifts. Essential for very high power tiptronic versions where the maximum reduction available via the stock ECU is not enough to prevent damage to components
• Ability to change torque ramp in after launch
• Change throttle blip requests to match your torque band. Especially useful on oversized turbo installations.
• Run up to 7bar map sensors
• Control high or low impendence injectors
• Control up to 12 injectors for high power installations where staged injection may be required
• Change injector dead times based on voltage levels for proper control
• Change injector end angle to ensure injection point is properly calibrated
• Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
• Ability to use any size DBW throttle body e.g. Chevrolet LS7
• Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
• Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
• Connect any race series dash including our own Syvecs Edition SDM displays
• View any input live with built in scope up to 1000hz
• and much, much more

Plug and Play 4.5 Bar MAP and Boost Pressure Sensor Kit for the Audi 4.0 TFSI engine

By simply pluging in the PnP kit, a whole new level of control is available allowing some of the following features:

• Direction Injection and Port Injection Support – 12 injector Option
• PDK Supported
• VTG Supported
• Up to 12 Maps to switch between
• Adjustable Traction control
• Adjustable Launch Control
• Adjustable Knock control
• Adjustable Direct Injection Pump control
• Rolling Antilag
• Pit Lane limiter
• Clutch Pressure adjustment and Fast Logging
• DTC Clearing from Onboard
• Live Tuning of every aspect of the engine’s calibration
• Ability to select desired engine map, boost level, traction and launch control levels through 12 Position switch or via OEM Steering wheel control
• Fully adjustable Launch control with Anti-lag strategies and Ramp in Maps
• Full Variable Valve Timing control
• Closed loop Lambda Control using OEM lambda
• Flex Fuel control
• Flat Foot Shiftings
• Fully adjustable closed loop boost control with launch level adjustments and trims for turbo speed, air charge, engine coolant temp, exhaust gas temperatures etc
• Monitor and trimming of exhaust gas temperatures
• Built in data logging using a market leading analysis software of up to 8 hours, with data rates at up to 1000hz
• Rolling Antilag / Pit lane limiter strategies, great for building boost on a roll
• Antitheft and valet modes
• Super fast connection via RJ45 Ethernet port for live tuning anywhere in the world or evenremotely if on track if connected to a wireless unit.
• Adjustable traction control strategies based on lateral g, steering angle and/or individual wheel speed monitoring.
• 4 programmable and selectable target slip maps. An immediate torque reduction can be applied by the ECU via ignition retard or a fuel cut.
• Configurable Engine Safety Trips on all important parameters like oil temperature, oil pressure.
• Fuel pump control of both main, and sub pumps, as well as Relative fuel pressure monitoring and limiting in the event of fuel pressure dropping on boost.
• 4 different Pedal to Throttle Angle maps with multipliers for different parameters e.g. speed. Again adjustable via steering wheel buttons
• Configurable individual cylinder closed loop knock control, to suit any cylinder modification with adjustments to frequency, windows for listening and gains for each cylinder. Ability to trigger full cylinder shutdown in severe knock conditions.
• Ability to change Torque ramp in after launch
• Run up to 7bar map sensors
• Change injector dead times based on voltage levels for proper control
• Change injector end angle to ensure injection point is properly calibrated
• Ability to fit any type of external sensor to monitor and trigger safety trips from anything from crank case pressure to damper position
• Ability to use any size DBW throttle body e.g. Chevrolet LS7
• Wet and Dry – Wet and Dry nitrous control with ability to drive solenoids directly and control n20 heaters via pressure monitoring
• Ability to control any external vehicle features based on sensor inputs e.g. Adjustable rear wing linked to G force or exhaust control valves
• Connect any race series dash or even one of our partners’ Touchscreen CANBUS adjustment /display units
• View any input live with built in scope up to 1000hz
• And much, much more!

Note: Can't be combined with other coupon codes

Tial Wastegate MVI Actuators specifically for the Audi 4.0TFSI engine.

Includes Direct Fit Brackets, Wastegate actuators, MAC Valve Boost Control Solenoid, Vacuum Hose, and Tee Fitting.

& 

Ready to run higher than 30psi of boost on your Audi 4.0TFSI Engine? We've got you covered. This simple plug and play kit includes everything you need to upgrade your pressure sensors to 4 Bar Absolute (~43.5psi of boost)

Includes:

(1) Manifold Air Pressure and (2) Boost Pressure Sensors

Custom DME/ECU tuning is required for this product.

Need customized tune settings beyond what the Dyno Spectrum OTS maps provide?

Rolling anti-lag

Pops and bangs

Exhaust flap and sound tuning

Rev limiter changes

4 Bar map sensor implementation

DS1 port injection, meth injection, nitrous controller implementation 

THIS SERVICE DOES NOT INCREASE POWER OUTPUT.  For more involved custom calibrations to increase performance, you must speak directly with one of our representatives.